T – Open Hopper Pump
	T – Open Hopper Pump When Things Get Really Thick seepex pumps of product group T are used for high-consistency material with low degree of intrinsic flowability or none at all. For these pumping products, the suction lift capability of a standard pump of product group N is no longer sufficient to suck them into pipings. For this reason, pumps of product group T are equipped with a feed hopper and facilities for safe product feeding. It is successfully used in almost all branches of industry to pump viscous to airtight products. T – Open Hopper Pump Flow rate | 50 l/h - 500 m³/h | 0.220 USGPM - 2,200 USGPM Pressure | up to 36 bar | 540 PSI   Advantages and Characteristics Pump with feed hopper and conveyor screw Pitch and diameter of the conveyor screw is adapted to the operating conditions for optimum product feed Optimum solutions for various viscosities and characteristics of the conveying medium Numerous ranges, optionally available in block design or with free shaft ends Service-friendly due to plug-in connections between rotating unit and drive   Ranges   Range BTQ For conveying medium to highly viscous products with a low degree of flowability Conveying capacities: 50 l/h - 100 m³/h 0.22 USGPM - 440 USGPM Pressures: up to 24 bar | 360 PSI read more     Range BT For pumping highly viscous products with a low degree of flowability. Conveying capacities: 100 l/h - 300 m³/h 0.44 USGPM - 1,320 USGPM Pressures: up to 36 bar | 540 PSI read more     Range BTM Developed especially for processing fruit and vegetables Conveying capacities: 0.25 m³/h - 130 m³/h 1.1 USGPM - 572 USGPM Pressures: up to 24 bar | 360 PSI read more     Range BTE For pumping highly viscous to airtight products that do not tend to bridging Conveying capacities: 0.5 m³/h - 100 m³/h 2.2 USGPM - 440 USGPM Pressures: up to 36 bar | 540 PSI read more     Range BTI For pumping highly viscous to airtight products that tend to form bridges Bridge breaker with two counter running rotating paddle shafts and a separate drive Conveying capacities: 100 l/h - 130 m³/h 0.44 USGPM - 572 USGPM Pressures: up to 36 bar | 540 PSI read more     Range BTH For pumping highly viscous to airtight and shear-sensitive products that tend to form bridges Separately driven ribbon screw rotating concentrically and on the edges Conveying capacities: 0.5 m³/h - 130 m³/h 2.2 USGPM - 572 USGPM Pressures: up to 36 bar | 540 PSI read more     Range BTHE For pumping highly viscous to airtight products that tend to form bridges Ribbon screw rotating concentrically and on the edges Conveying capacities: 0.5 m³/h - 130 m³/h 2.2 USGPM - 572 USGPM Pressures: up to 36 bar | 540 PSI read more     Range BTES For pumping highly viscous to airtight products from silo systems. Conveying capacities: 0.5 m³/h - 130 m³/h 2.2 USGPM - 572 USGPM Pressures: up to 24 bar | 360 PSI read more     Range BTEI For pumping highly viscous to airtight products that tend to form bridges Bridge breaker/mixing device with rotating paddle shaft and a separate drive Conveying capacities: 0.5 m³/h - 100 m³/h 2.2 USGPM - 440 USGPM Pressures: up to 36 bar | 540 PSI read more		Pump Selection Program